4 Inch TC Pressure Lid
"Good for using Fermzilla hop Bong on stainless fermentation vessels or a Kegmenter."
4 Inch TC Pressure Lid with 2 Inch TC Port
$9.95
Sale price
$9.95
Regular price
Skip to product information
In stock
4 Inch TC Pressure Lid with 2 Inch TC Port
KL35965
$9.95
Sale price
$9.95
Regular price
Get a better RAPT Pill WiFi reading with the all new Kegmenter Lid from KegLand. Suits any standard 4 Inch Tri-Clover Ferrule.
Reinforced Industrial Plastic 4 Inch TC pressure lid with 2 Inch TC port. Suits a 35psi RED Pressure relief valve and two carbonation caps. You can also fit a temp twister and 600mm thermowell probe into it.
Due to the large 4 Inch Tri-Clover diameter, it is difficult to get higher pressures without leaking. Therefore we suggest using this up to 1.5 BAR (21psi)
This should only be used with a Red 35psi PRV (Pressure Relief Valve) or the Yellow 17psi PRV
1 x KL05333 Red 35psi PRV
or
1 x KL22569 Yellow 17psi PRV
We would also recommend the following extras if you do not have them already:
1 x KL10788 - RED Multi Gas Post Plastic Carbonation Cap
1 x KL10788-Yellow - YELLOW Multi Liquid Post Plastic Carbonation Cap
1 x KL04602 - 4 Inch TC Clamp Beaded Seal
1 x KL32902 - 4 Inch TC 3 Segment Clamp
1 x KL03438 - 2 Inch TC Clamp Beaded Seal
1 x KL03322 - 2 Inch TC 2 Segment Clamp
1 x KL27564 - 2 Inch x 2 Inch Butterfly Valve
1 x KL23627 - PCO1881 Male x 2 Inch Tri-Clover (POK)
1 x KL26079 - 2 Inch Hop Bong
1 x KL20176 PCO1881 PRV Cap (for hop bong)
Extra 1 x KL05333 Red 35psi PRV (for hop bong)
Extra KL10788 RED Multi Gas Post Plastic Carbonation Cap (for hop bong)
Extra KL03322 2 Inch TC 2 Segment Clamp (for hop bong)
Extra KL03438 - 2 Inch TC Clamp Beaded Seal (for hop bong)
You may also like
Overall rating: 4.5 / 5 from 10 reviews.
AI Generated Review Summary
Summary topics
Review topics: [pressure].
Review highlights
Reviews
Easy to use
"Better than the old lids and handy you can also buy it with the ports pre drilled or not. I bought it for my stainless fermenter so I can use a Pill"
Works well with the pill hydrometer.
"I bought this along with the rest of the fittings to improve the signal from my pill through a kegmenter. Works a treat. Never dropped out once."
Perfect.
"Works just fine. Using the old stainless lid on a kegmenter the transmission from the pill to the temp controller would fail several times and would default from the pill to the fixed probe. Temperatures were all over the place. With the plastic lid there were zero dropouts. I'm sold on this piece of kit and just bought another."
4 Inch TC Pressure Lid for my Kegmenter
"I bought this so Ican use the hop bong setup I purchased ontop of my kegmenters when brewing for no oxygen hop additions. Will be a game changer"
New lid
"Good product"
Pressure lid
"Clamp the pressure lid to any 4inch tc. Great pairing to the kegmenters"
Get it tight and it will work…
"Was worried in the beginning because I couldn’t get the lid to seal. Consistently leaked from the TriClamp ring even at low pressures. Finally got it to seal by tightening to the point I thought I would break it. Holds pressure now. Have it attached to kegmenter with Kegland temp twister cooling coil and thermo well along with DIY glycol chiller."
Unfortunately it leaks
"Leaks. I can’t get the 4” tri clamp to seal no matter how hard I tighten."
Great product
"Bought this product so as to receive the rapt pil signal from a kegmenter. Works very well"